Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mellowness65

Pages: [1] 2 3 ... 23
1
Projects and Worklogs / Re: 98 ZX2: Mellowness65(many pics)
« on: June 29, 2011, 07:01:20 PM »
Ok so it's been a while since my last update, I got all the speakers installed courtesy of my housemate(carfi installer for BestBuy), the speakers were all Alpine Type R, components up front, 5x7's in back, and a single 12" sub in the trunk.  Needless to say the sound is exponentially better than before.  I've got a Vit tune on the car now, it feels a little better than NGP0 but I've not gone to a dyno to see where I'm at though it has kind of interested me to see the change.  All parts are in for the head swap but I've not gotten the time, space to do it, or money for custom tuning as of yet. That should be around soon enough, hopefully the install will go down sometime before school starts in August and is delayed indefinitely again.  I broke/wore out my axle again in May, after replacing the axle and retaining the halfshaft, the bearing in the half finally went bad and wore out that end of the axle as well, meaning the lifetime warranty didn't help for anything as the halfshafts are NLA thru Ford. I replaced the ps axle with the 3rd gen sedan passenger axle that doesn't use the halfshaft but also comes with the lifetime warranty, problem solved.  Also I was able to finally get centercaps for the SSR wheels, at $35 apiece they weren't cheap, but if thats all I need for a forged set of 17's to look good I consider it money well spent.

2
ZX2 Discussion / Re: got no spark
« on: June 28, 2011, 07:30:48 AM »
did you change the cam sensor housing? the sensor itself isn't the important thing to change, its the metal piece  that holds it

3
Off-Topic / Re: New to zx2s and already loving them
« on: February 27, 2011, 09:49:42 PM »
They're fun and cheap to work on, where's it hit at?

4
ZX2 Discussion / Re: OBX Headers
« on: November 25, 2010, 06:24:47 PM »
There's no noticeable difference between a zxtuner and kami header, since kami's the only one on the market it's your route to go. The gude is rare at best and a real mofo to fit. Plus its really vulnerable to denting on the lower primaries

5
Brakes/Suspension/Wheels and Tires / Re: Brake Setup?
« on: November 25, 2010, 06:21:26 PM »
A rear disc setup with stainless lines and ceramic pads is all you need as long as you're n/a or a small turbo. They'll lock up crappy tires(I know) and almost do the same with stickier 205 series tires

6
Projects and Worklogs / Re: 98 ZX2: Mellowness65(many pics)
« on: August 01, 2010, 09:04:39 PM »
THIS JUST IN: My car looks good :lol:

Beater is almost road ready, I'll be glad when it is

FR valves for my new head, sent to JohnP, the mani is going tomorrow hopefully.
New stereo shiz, I just need door components and I'll be set

7
Problems, Parts and Diagnosis. / Re: Engine Harness
« on: August 01, 2010, 08:14:47 PM »
$20 shipped, its the small wiring harness that plugs into most if not all sensors on the actual motor

8
I'd try a different maf if unplugging it made no difference. A zx2 idles rough with ac on at idle, it's just a fact so I wouldn't worry too much on that part. If the o2's were faulty you'd get a code specifically for them. the iac is an expensive part that i wouldn't replace unless i was certain that it was the cause

9
Problems, Parts and Diagnosis. / Re: Engine Harness
« on: July 30, 2010, 07:36:28 PM »
I have one if you can't find one locally

10
Problems, Parts and Diagnosis. / Re: Engine Harness
« on: July 25, 2010, 11:00:29 PM »
it doesn't require anything, it'll just be an extra plug

11
Problems, Parts and Diagnosis. / Re: Engine Harness
« on: July 21, 2010, 07:25:54 PM »
those arent on the actual engine harness. the only thing I can think of is that a 98 will have a extra sensor on the fuel rail that later years do not

12
Problems, Parts and Diagnosis. / Re: Engine Harness
« on: July 16, 2010, 06:38:02 PM »
yes

13
Projects and Worklogs / Re: 98 ZX2: Mellowness65(many pics)
« on: July 15, 2010, 03:09:40 PM »
Took a 4.6L tb apart, it's what I'll be using with the frim. Also took apart a stock zx2 tb, as you can see it'll be a vast improvement



14
Problems, Parts and Diagnosis. / Re: Need Help With Cam Decision
« on: July 10, 2010, 07:47:26 PM »
porting def. helps the head, that's why ford did it on the svt focus ;)

15
Drag Racing / Re: Taking my zx2 to the track for the first time
« on: July 10, 2010, 07:46:15 PM »
launch very, very carefully

Pages: [1] 2 3 ... 23